admin 20 November, 2018 0

ISO 10816-1 PDF

Revisions / Corrigenda. Previously ISO · ISO · ISO /Amd ; Now ISO 15 Dec PDF disclaimer. This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed. The International Standard ISO has the status of a Swedish Standard. This document contains the official English version of ISO

Author: Kajidal Brazilkree
Country: Andorra
Language: English (Spanish)
Genre: Sex
Published (Last): 26 September 2010
Pages: 15
PDF File Size: 15.92 Mb
ePub File Size: 15.87 Mb
ISBN: 798-3-59034-303-6
Downloads: 4263
Price: Free* [*Free Regsitration Required]
Uploader: Mazujin

This is an open access article distributed under the Creative Commons Attribution Licensewhich permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Algorithm evaluation of the equipment based on the vibration measurement methodology presented together with the flow diagram of the diagnostic information from the sensor through the signal processing, the maximum value of the spectrum in the spectral analysis of the acceleration, the velocity and the displacement of the vibration and determines the effective value of the vibration in the band Hz presents in the following section [2].

The standard requires a velocity measurements in three axes X – Y – Z. A — good, B — satisfactory, C — unsatisfactory, D — unacceptable.

BS ISO 10816-1:1995+A1:2009, ISO 10816-1:1995

There are numerous standards that provide guidance for determination of an acceptable level of vibration parameters selected as the measurement shall be performed, and how the collected data should be analyzed.

Evaluation of mechanical vibration by measurements on non-rotating parts — Part 1: Final text received or FDIS registered for formal approval. The results are dependent on air temperature, humidity, magnetic, vibration, other equipment, and installation errors.

However, the ISO series is also applicable to measurements made on other rotating elements if such elements are found to be more suitable, provided that the guidelines are respected. Next are estimated the effective velocities V R M S. To obtain correct results are used properly prepared parts of the measuring circuit to eliminate the factors affecting the measurement. Received 29 September ; received in revised form 23 November ; accepted 1 December ; published 30 December You may experience issues viewing this site in Internet Explorer 9, 10 or Introduction The decision making process on the state of the machine is usually assisted by technical diagnostic methods and determined by different types of indicators attributes, symptoms.

TOP Related Articles  1746-NO4V DOWNLOAD

The last graph is the expressed spectrum shift, as d f function. 108166-1 calibration VibroTest system in laboratory condition, was established the measurement error. Nowadays there are a huge number of technical solutions to construct and the different types of the components of the measurement system [8].

The last element of this algorithm is the record of the data and the selection of a new program or exits the application. The result isso an application that allows the analysis of the vibroacoustic signals, based on the ISO standard [19].

Evaluation des vibrations des machines par mesurages sur les parties non tournantes.

The final score of the program is the task of determining the status of the test machine. Guidelines for uso selection parameters of the measurement sensors The quality of the transducers effects on the quality of the data. General view on components of the machines diagnostics system. These standards have been revised by ISO The decision making process on the state of the machine is usually assisted by technical diagnostic methods and determined by different types of indicators attributes, symptoms.

Good standards, which for many years are reference point formed by gather opinions of the broad masses of users, and thus are widely accepted and used. iwo

The most important parameters which contents the calibration chart are: The four groups are distinguished machines that are divided into power and their 108166-1. Accept and continue Learn more about the cookies we 10816-11 and how to change your settings. General view on components of the machines diagnostics system [] with particular regard to the required knowledge necessary to design diagnostic system and correct inference about the state of the machine is shown in the Fig.

NOTE 1 The evaluation criteria for different classes of machinery will be included in other parts of ISO 1016-1 they become available. The arrangement of the accelerometers of the system for measuring and evaluating the vibration condition of the machine under test as a subsystem of diagnostic systems of parameters of the electrical machines.

TOP Related Articles  FRANK DUBIEL DA BOOK PDF

For the purposes of ISO uso, operational monitoring is considered to be those vibration measurements made during the normal operation of a machine. Measurement error is greater for the double integral and is 3. Machines that generate vibroacoustic processes are tested at every stage of their life cycle. Please download Chrome or Firefox or view our browser tips. We use cookies to make our website easier to use and to better understand your needs.

These experiments resulted in: The ISO series permits the use of different measurement quantities and methods, provided that they are well-defined and their limitations are set out, so that the interpretation of the measurements is well-understood. Therefore, next to a table with maximum values, there are four indicators similar to LEDs that are to inform the user who is responsible for the condition of the tested machine.

The reliability of the research requires, to recall the precise equipment used for this research. The next chart is the velocity spectrum expressed, as v f. The contributed to the development of all kinds of monitoring systems and diagnostic inference. It is applicable to measurements of both absolute and relative radial shaft vibration with izo to the monitoring of radial clearances, but excludes axial shaft vibration.

The system for measuring and evaluating the vibration condition of the machine under test is a subsystem of diagnostic system of parameter of electrical machines and diesel engines on ships.

Modern measurement tools are often based on virtual instruments and apparatus. Evaluation of machine vibration by measurements on non-rotating parts Rotodynamic pumps for industrial applications, including measurements on rotating shafts BS ISO Class I — machines may be separated driven, or coupled units comprising operating machinery up to approximately 15 kW approx 20 HP.

This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.

Take the smart route to manage medical device compliance.